Water heater relining
Smaller liners for gas or oil furnaces and water heaters stop condensation from damaging the chimney.
A sweep in Wanaque can reline an unlined or damaged flue to protect the masonry and keep heat away from the framing around it. Dial (862) 355-2009 to talk with a local chimney pro about relining.
The liner is what smoke travels through on its way out of the house. It keeps heat from reaching wood framing next to the chimney, protects the brick and mortar from corrosive gases and gives the appliance a flue of the right size to draft well. In older houses, it is common to find an unlined chimney or a clay tile liner that has failed.
Most liner installations start with one of these situations. Damaged clay tiles, missing mortar between tiles or no liner at all are the most common triggers. Installing an insert, stove or high efficiency furnace often means the old flue is the wrong size.
Before relining, the chimney should get a thorough inspection, usually a Level 2 inspection with a camera run up the flue. That reveals whether the existing tiles can be repaired or need to be replaced, and it shows the route a new liner will take. Ask to see the camera video so you understand what was found.
If the problem goes deeper than it first looked, a Wanaque chimney sweep may also recommend chimney liner repair or chimney inspection.
Dealing with this in Wanaque, NJ right now? Call (862) 355-2009 to talk to a local chimney sweep.
Call nowHere is how a sweep usually handles a liner installation.
The sweep inspects the flue from top to bottom, usually with a video camera. The findings shape the rest of the job.
The right diameter depends on the stove, insert, furnace or fireplace being vented. The length is measured from the appliance to the top of the chimney.
Before the liner goes in, the chimney is swept and cleared. Some chimneys need old tiles broken out to fit an insulated liner.
A flexible liner is fed down the flue, while rigid sections are joined as they go. Insulating it helps draft and reduces creosote and condensation.
The bottom connects to the stove, insert or appliance, and the top is sealed with a top plate and cap. The connections keep gases from leaking into the old flue.
The appliance is fired or the draft is tested to confirm smoke and gases go up and out. Make sure working CO alarms are in place near sleeping areas.
Smaller liners for gas or oil furnaces and water heaters stop condensation from damaging the chimney.
Flexible stainless steel liners bend around offsets in the chimney which makes them the most common relining choice.
A cement based mix is poured around a form inside the chimney to create a smooth new flue which suits some older or irregular chimneys.
Straight flues can take rigid stainless pipe and holds up to frequent cleaning.
Liners can be insulated with a blanket or a poured mix to keep flue gases warm and meet clearance requirements.
A stainless steel liner is the standard choice for most homes that need a new flue. Flexible liners make it possible to reline chimneys with offsets, while rigid pipe gives a smooth, heavy wall. The grade of stainless and the wall thickness are matched to the fuel, and systems are tested and listed as complete kits with their parts.
Stainless liners are often paired with insulation, either a wrap or a poured mix, which keeps flue gases warm and can be required for clearance to combustibles. At the top, a sealing plate and cap keep rain and animals out. In Wanaque, a stainless liner is a common upgrade when installing an insert or wood stove.
Relining means putting a new liner into a chimney that has an old, damaged or missing one. Changing to an insert or stove, finding cracked tiles or recovering from a chimney fire usually leads to relining. Most chimneys can be relined from the roof without opening walls.
When you call (862) 355-2009, tell the sweep what vents into the chimney, such as a fireplace, stove, furnace or water heater. A furnace replaced with a high efficiency model that vents through the wall can leave the water heater alone in an oversized flue, which leads to poor draft and condensation. A smaller liner brings the draft back where it should be.
Many chimneys in Wanaque were built long before modern liners were standard. Across Wanaque and nearby towns such as Bloomingdale, Oakland, Pompton Lakes and Pines Lake, long heating seasons and repeated freeze and thaw cycles are hard on clay tile and mortar, so it is worth having the flue inspected before the next heating season.
Need chimney liner installation around Wanaque? Call (862) 355-2009 for a Wanaque chimney sweep who serves the towns around it too.
Winters here are long and cold, and the heating season usually runs from October well into April. The hardest thing on brick here is not the cold itself but the constant swing above and below freezing: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, which is how cracks, loose bricks and leaks start. Nor'easters drive rain sideways into flashing and mortar that looked fine in summer. Most homeowners in Wanaque, NJ schedule a sweep in early fall, and a repair check after a hard winter.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Wanaque know the chimneys and fireplaces common in local homes.
Ask your questions before you agree to anything.
More questions? Call (862) 355-2009
Fixing gaps, cracks and missing mortar inside the flue liner with resurfacing, joint repair or partial replacement.
Learn moreAn annual look at the flue, firebox, damper, crown and cap before a sale, after a chimney fire or ahead of the heating season.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, with the chimney inspected before anything goes in.
Learn moreSetting up a new wood stove from hearth pad to chimney cap, with stovepipe, liner or chimney sized to the stove.
Learn moreLooking for something else?
See all chimney servicesCall (862) 355-2009 to talk to a chimney sweep serving Wanaque, NJ.
Free to call. No forms to fill out.